Purchase your copy of BS EN ISO +A as a PDF download or hard copy directly from the official BSI Shop. All BSI British. Buy EN ISO Plastics Piping Systems For Industrial Applications – Acrylonitrile-Butadiene-Styrene (Abs), Unplasticized Poly(Vinyl Chloride) (Pvc-U) . Buy ISO PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS – ACRYLONITRILE-BUTADIENE-STYRENE (ABS), UNPLASTICIZED.
|Published (Last):||12 December 2009|
|PDF File Size:||7.79 Mb|
|ePub File Size:||8.66 Mb|
|Price:||Free* [*Free Regsitration Required]|
NOTE Attention is drawn to the need to take account of any relevant legislation relating to the colour coding of piping in respect of its purpose or contents for the location in which the components are intended to be used.
Copyright Copyright subsists in all BSI publications. Jointing face for flat seal Jointing face with O-ring groove Figure C.
The values of the minimum required hydrostatic strength see reference curves given in Figure B. For the design of a piping system e. The material shall be as classified by the raw-material producer. Please first log in with a isk email before subscribing to alerts. The listing is therefore given for information only and is not intended to indicate technical conformity between the documents.
It neh lnuikletneve y ttah a lborpem leratign ti ot is fnuo,d lpsaee ifnrom ttneC ehlar Secrteirata at tsserdda eh igleb nevwo. For external above-ground installation, additional requirements depending on the climate kso be agreed on between manufacturer and purchaser. Metric series ISOFittings, valves and other piping system components made of unplasticized poly vinyl chloride PVC-Uchlorinated poly vinyl chloride PVC-Cacrylonitrile-butadiene-styrene ABS and acrylonitrile-styrene- acrylester ASA for pipes under pressure — Resistance to internal pressure — Test method ISOThermoplastics materials for pipes and fittings for pressure applications — Classification and designation — Overall service design coefficient ISOThermoplastics materials — Preparation of tubular isoo pieces for the determination of the hydrostatic io of materials used for injection ieo ISO Dimensions, tolerances and designation ISOPipe threads where pressure-tight joints are not made on the threads — Part 1: Document Status Indicators The Green document status indicator indicates that the document is: The components have to withstand the mechanical, thermal and chemical demands to be expected and have to be resistant to the fluids to be conveyed.
EN ISO 15493:2003
NOTE 154933 Where relevant, national regulations for specific applications e. Already Subscribed to this document. Dimensions, tolerances and designation ISOPipes and fittings of plastics materials — Fittings for domestic and industrial waste pipes — Basic dimensions: This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations.
Your Alert Profile lists the documents that will be monitored.
EN ISO – Plastics piping systems for industrial applications – Acrylo –
Plastics piping systems for hot and cold water installations – Crosslinked polyethylene PE-X – General You may be interested in this related standard. Attention is drawn to the fact that, for a particular test method, the technical content of the International Standard and the European Standard may be different.
We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. If values for the out- of-roundness other than those given in Table A. Test assemblies for pressure tests shall be closed with pressuretight end-load-bearing end caps, plugs or flanges which shall be provided with connections for the entry of water and release of air.
BS EN ISO 15493:2003
For S and SDR, the respective values for the corresponding pipe shall be taken. Other colours shall be agreed on between manufacturer and purchaser. In all cases, the fitness for purpose of the components shall be demonstrated.
The work of preparing International Standards is normally carried out through ISO technical committees. It is identical with ISO For undated references, the latest edition of the normative document referred to applies. Where fittings and valves are manufactured from the same material as pipes, the material classification shall be the same as for pipes. A list of organizations represented on this subcommittee can be obtained on request to its secretary.
ISO shall not be held responsible for identifying any or all such patent rights. Liquid bath or Longitudinal reversion a Temperature Immersion time: Other requirements and other EU Directives may be applicable to the products falling within the scope of this standard.
It is important to us that you purchase the right document.