Intecont Tersus – Free download as PDF File .pdf), Text File .txt) or read for weighing tasks better than % Manual and/or automatic zero setting Full. The INTECONT Tersus weighing elec- tronics is specially tion module, INTECONT Tersus optimally fits into any Manual and/or automatic zero setting. processes, the INTECONT Tersus meas- uring, control, and supervisory module, INTECONT Tersus optimally fits into any Manual and automatic zero setting.

Author: Vogore Dajas
Country: Panama
Language: English (Spanish)
Genre: Medical
Published (Last): 13 September 2007
Pages: 478
PDF File Size: 1.55 Mb
ePub File Size: 9.87 Mb
ISBN: 519-1-45125-165-7
Downloads: 61645
Price: Free* [*Free Regsitration Required]
Uploader: Mutilar

Additionally, you should observe: XC1 DeviceNet module front viewFig. Important features at a glance Compact evaluation electronics for continuous measurement systems Colour, high-resolution TFT Ergonomic operating elements arranged by function Multilingual capabilities provided by the operating languages available.

Call up the function block Calibration Set Time Abort possible at any time Enter the year, month, day, hour, minute and second. The totalized amount of material dispatched is directly recorded. The dimension data should be adapted to the Nominal Flow Rate.

Special start-up and empty running functions can also be activated. Intecont Tersus Apresentao das diferenas Documents. Yersus with calibration weights: One particular benefit is the fact that the configurable scale values are available in the CFC plan itself as binary or numerical values.

If the optional activation is required on devices which have already been delivered, the data is transferred to the Schenck process, and the generated activation code is reported back.

There is the danger of injury if persons are in the area of the drives. Calibration active is shown in the header. Connection diagram for ITE inputs and outputs Fading out may result in breaks in the numbering.


Out of Tolerance W1 P The force is conducted centrally into the load cell. Check the output regulator settings current limiting, speed range – Calibration error: WZ connection diagram and tachometer Watch belt circuit sensor service value; if need be, remedy fault.

Tare or zero 2. It describes the functionali-ty of the VWF xxx software. This changes the speed of the conveyor belt until the actual value is equal to the setpoint. Zero setting The zero point fault of the belt weigher comes from soiling that adheres permanently or from other con-stant factors.

Then it shows the new setting for a couple of seconds as Current Time. There is danger of contacting live parts.


It can have a direct effect on the weighing platform or via a lever nitecont. Clean tail and drive pulleys. Intecont Tersus Schenck Calibration Manual pdf Key in the final result of zero setting program and key in later in Linearization I1 parameters. Namur Error Tacho A P On vertically-installed load cells, the effective angle equals 0.

Relevant data in the middle and lower display zone: Any reproduction of this documentation, regardless of method, without prior permission by Schenck Process GmbH in writing, even by excerpt, is prohi-bited. Select the desired function of the second level. Bvhgb Instruction Manual Intecont Documents. Some parameters can be write protected. The Service Values chapter explains the specific data in detail. Single-Idler Platform The load on the weighing platform is conducted via a weighing idler into the load cell.

INTECONT Tersus is a measuring and measurement processing system of continuous weighing and feeding equipment for weighfeeders conveyor belt scales differential feeding scales Coriolis mass flow equipment and solids flow equipment. The programs can only be used for belt monitoring if there is a belt circuit sensor Namur transmitter and a triangular metallic sensor surface in the conveyor belt.


However, it is always expe-dient to measure the length manually and to enter the exact value as a parameter. Then it automatically asks for the Batch Setpoint Source. The mounting orientation of the load cell is the decisive factor. The hatched area shows the load distribution on the weighing platform. Follow all instructions to prevent this from occurring. The measuring system can be part of a more complex plant. Key in the sensor length in P Special languages such as Chinese and Russian can also be loaded Automatic adjustment programs.

Gravimetric Controlled operation as described above Volumetric Uncontrolled operation, i. Call up the function block The previously selected function will be displayed if no event is pending. Hidden parameters can only be shown with the EasyServe service software and they can also be cleared there for the dis-play on the unit wherever necessary.

Manual Intecont Tersus

Change back to the first level. Minor risks may arise in these situations if the measuring system is used or operated by untrained personnel. Any use other than intedont intended is considered inappropriate. This means that if the belt load changes, the measurement result for the feed rate will not accord precisely with the current feed rate at the dispatch point.