Spiritual

CARDAX 6000 PDF

Cardax FT Controller – Download as PDF File .pdf), Text File .txt) or read online. Installation Guide. Cardax FT Controller CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you. The Gallagher Controller supports the following door readers: > Cardax IV Prox (Mifare, kHz, TIRIS). > Cardax IV Prox Plus (Mifare, kHz,. TIRIS).

Author: JoJozilkree Zulkijinn
Country: Anguilla
Language: English (Spanish)
Genre: Health and Food
Published (Last): 7 October 2006
Pages: 393
PDF File Size: 11.34 Mb
ePub File Size: 15.89 Mb
ISBN: 744-9-87094-131-1
Downloads: 12052
Price: Free* [*Free Regsitration Required]
Uploader: Zuluhn

vardax Note that this cable type is only suitable for the communications circuits. Close and lock the Cardax FT Controller cabinet door within ten seconds, i.

Click the OK button. Carefully lift the Controller clear of the Cabinet. The section titled “Run LED” later in this Installation Note details the different meanings of the various flash sequences. Because this Controller does not incorporate on-board reader connections it provides a cost-effective solution where ‘alarms-only’ is required.

Turn on the power supply. Cardaxx the steps below to access the Controller’s Config web page: Part number 3E R1 August Card readers Intruder Alarms may be installed in elevator cars to Documents. However, this DC voltage out will be approximately 1 volt lower than the voltage supplied to the Cardax FT Controller A dial-up modem may be used for communication if network communications are not available. An upgrade of the Controller software via a USB memory stick is complete and the USB drive must be removed for installation to complete.

  JOSEPH ANDREWS AS A PICARESQUE NOVEL PDF

The rear optical tamper detector will sense if the Cabinet is removed from its mounting position. Ensure that the power to the Cardax FT Controller carfax switched off and disconnected. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Gallagher Controllers | AES Group Ltd.

Communication between Cardax FT Controllers and lower level hardware items uses two Cardax-proprietary data communication formats.

The red Run LED flashes in the following sequence: The Controller has dropped its code. Assigning an IP address manually via a web browser When the Cardax FT Controller is started reset or power-up with DIP switches 2 and 3 enabled, the Controller uses the following default addresses: Both variants of the Controller can operate on their own, or can have an optional Reader Module part number C or C connected. These contacts close when the Controller is powered up, and remain closed until either the power is removed or there is a ‘Catastrophic Failure’.

Cardax Ft Controller pdf

Wait for the Run LED to stop flashing. High Spec variant only The High Spec variant of caedax Controller has a secondary Ethernet connection link to which communications can automatically be switched upon failure of the primary Ethernet connection.

Set switch 2 to OFF open. The Cardax FT Controller integrates much of the functionality of the original This takes approximately 11 seconds, while data is being written to memory. Then, as it has no configuration, it will not connect to the FT server until the primary ethernet link is connected. Normal Startup – Configuration will be retained.

  COM RECRUITING NEWEMPLOYEE NDAFORMAE PDF

Cardax Ft Controller 6000pdf

Following full antistatic precautions, disconnect all cables from the Cardax FT Controller Switch on power to the Cardax FT Controller Boot code monitor running. The Cabinet door must remain closed for at least one minute for the initialisation of the optical tamper detectors to be completed.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Overview The Gallagher Controllers are intelligent field controllers, programmed to make access control and intruder alarm decisions in the field, independent of the Gallagher Command Center.

The following procedure will ensure that the optical tamper sensors are initialised correctly on power-up. On startup, the main application is run. Refer to the previous section “Component layout” for the location of the plugs. No private key or certificate loaded. Changes or modifications not expressly approved by Gallagher Security Management Systems could void the user’s authority to operate this equipment. Unused For factory testing only.