Boxart Avro Lancaster B.1(F.E.)/ A Airfix Instruction sheets Avro Lancaster (Special) The Dambusters (Airfix A Airfix model kit in scale , A is a NEW tool released in | Contents, Reviews, History + Marketplace | Avro Lancaster. Operation Chastise – RAF Scampton | May ; Avro Lancaster B GB Military Instruction sheets. Airfix Instruction Sheets available for free download. ; Apollo Saturn V – SK (Courtesy of Guy De Witte); Avro Anson I – ; Avro Lancaster –
|Published (Last):||4 October 2017|
|PDF File Size:||8.93 Mb|
|ePub File Size:||3.71 Mb|
|Price:||Free* [*Free Regsitration Required]|
First introduced into RAF service inthe basic form of the Avro Lancaster heavy bomber changed little during its production run and the Mark 1 continued in production to the end. With the dropping of Atomic bombs by US forces, there was no requirement for deployment but the near-new airframes were available to equip the squadrons of a much-reduced RAF Bomber Command in the early years of peace. These specialised Lancasters were intended to be part of Tiger Force, an integrated strike and transport force that would range over the Far East in and beyond.
Bomber Command was drastically reduced to a peacetime complement of some Lancasters spread across 22 Squadrons. The nearly-new Tiger Force Lancasters went into service while hundreds of war-weary airframes headed for the scrap yard and the type was gradually supplanted by the successor Avro Lincoln, a process completed by late Airfix have made good use of the basic tooling for their 1: II reviewed in October There have been subsequent releases as gift sets covering the Dam Buster and standard Mk.
The parts were free from flash and none seemed to be warped. Surface detailing is mainly recessed panel lines that some may consider being too deep but I found them to look OK under a coat of acrylic. There are no stores provided for the bomb bay but Airfix provide suitable weapons as a separate accessory set. An A4 sized instruction book runs to 24 pages and steps of construction. There are two pages of colour three-views as a colour and decals placement guide.
Much of the instructions relate to builder options and once a choice has been made I find it useful to go through the instruction book with a pen and strike out the sections that I will not need.
Airfix has carefully designed its Lancaster tooling to cover many of the detail differences between Mks and the early and late production versions of the same Mk. They are clear as to which parts are needed for each version in the kit but there are some parts that are only applicable to other boxings of Lancaster.
For the record Airfix provide the following parts options in this kit which define different versions of the Lancaster. Flat or bulged cockpit side windows. Optional H2S radar scanner under the belly. Mid upper turret or blanking plate. Shrouded or unshrouded engine exhausts.
Airfix 1/72 Lancaster B.I (F.E.), by Frank Reynolds
Standard or paddle blade lxncaster. So there is plenty of scope for conversions or alternative finishes. Airfix does not however provide some of the elements of very late build aircraft such as the taller astrodome to the rear of the flight deck, extended rudders or treaded tyres.
Decals are provided for the flashy white F. This neatly illustrates the strange designation system of Lancaster production where the MK. I offered in this kit has all of the late-build features, while the MK. Unstructions has the early build details. So when building other than straight from the box, good references are essential, especially photographs of the version being modelled.
As it is, when I came to the end a question remained. Building the basic Airfix Lancaster has been covered in the previous MM features referred to, so there is no need to repeat the details here and I will only cover the significant points relating akrfix this version. These need to be filled, although this is not made clear in the Airfix instructions. I find that this is best onstructions with at lwncaster early opportunity firstly by gluing the clear window strips in place, allowing them to set hard and then masking off the fuselage each side kancaster the strips with 6mm Tamiya tape before filling over the windows with Squadron Green Putty.
The tape can be removed before the filler dries leaving a raised ridge of filler that, once set hard, can be gently sanded down to a smooth finish. Lancasger quick blast of grey auto primer from a rattle can will seal the filler before the primer is sanded away as a check that the filler has covered all of the previous window openings. I then proceeded with the fuselage assembly as normal. Based on my previous efforts I have learned that following the build sequence as set out in the instructions is a sensible choice and following the options set out should give a satisfactory result.
The wings and tail structures could be treated as sub-assemblies if required. There are nevertheless a couple of potential glitches with awkward parts of the build. The main undercarriage is built into the airframe at a fairly early stage and needs to be masked and carefully protected thereafter. I have insturctions yet found a way around that problem and learned to live with it. The mid upper and tail turrets can be added at a very late stage after main painting is complete although the seating of the rear turret requires some trimming to get it to fit inside the fuselage fairing.
The nose turret is more of a problem in that it has a horseshoe shaped fairing surmounted by llancaster small acorn shaped fairing above the turret pivot.
Airfix Instruction Sheets
This is meant to be added after the turret is fitted and it is a real problem to try to get the turret to sit in place if this fairing has been first glued to the nose, without hacking away much of the turret base.
The alternative is to assemble and paint the turret, mask it and install at an early stage or to add the fairing at the end and touch in the paintwork. Any which way it is a bit of a fiddle. My standard procedure with these Lancasters is to treat the turrets as separate kits, make, and paint and finish them to be incorporated into the build as it progresses.
With care, steady progress can be made to arrive at a basic airframe, with wings, engines and tail attached, ready for painting. Although it costs over a quarter of the price of the basic kit, there are over perfectly die cut masks in Kabuki tape that can be applied with confidence that they will fit each panel of the glazing and saving what could be hours of work in having to cut each mask by hand.
Lancaaster applied, I gave the exterior of each masked clear part a quick blast of grey auto primer to provide a dark colour to the interior framing. The completed airframe was primed with Tamiya Ultra Fine White primer applied from a rattle can and a second coat of the same over the top and side surfaces as a finishing colour.
I find this product lacnaster have an excellent density and coverage. The demarcation line between the White and Black on the sides of the engine cowlings has a very distinctive swooping curve, so I made a stencil from 20thou plastic card to enable the masking on the labcaster panels to be trimmed to the same size and shape.
The decals were of good quality and reacted well with Micro Sol and Micro Set decals solutions. Airfix provides the wing walk markings and a range of airframe stencils.
The deal sheet is not vast and this stage of the build was completed over two evenings, before the decals were sealed with two misted airbrush coats of Xtracrylix Flat varnish. The White finish almost demands some sort of exhaust staining to the paintwork so a few light lancasrer of Tamiya X Smoke gave a hint of some service use to the aircraft.
The small external aerials were added and two llancaster windows in the fuselage spine were drilled out to be filled lancsater Micro Kristal Kleer. Propellers and undercarriage were added to complete the project. However, a query remains. I have found a single photo that shows at least one F. E to have a long external intake on the right side of the fuselage above the wing root.
Airfix Instruction Sheets
Indeed Revell provides such a component in their 1: Airfix have a good reputation for well researched colour schemes so should TW have such an intake or not?
I have a pre-painted Revell intake on stand-by to attach to this model if needed. The Airfix Lancaster has been deservedly well received by modellers and this version maintains the good standard.
The white colour scheme of the post war era is unusual and provides a dramatic contrast to the more dowdy night bombers in my collection. Not a shake instructtions bake build, but like most current Airfix kits it pancaster careful work and in the hands of those with more skill and application than I have a show-stopper can result.
Back to the Main Page. Back to the Review Index Page.